300-206 SENSS Implementing Cisco Edge Network Security Solutions
Exam Number 300-206 SENSS
Associated Certifications CCNP Security
Duration 90 minutes (65 – 75 questions)
Available Languages English, Japanese
Exam Description
The Implementing Cisco Edge Network Security (SENSS) (300-206) exam tests the knowledge of a network security engineer to configure and implement security on Cisco network perimeter edge devices such as a Cisco switch, Cisco router, and Cisco ASA firewall. This 90-minute exam consists of 65-75 questions and focuses on the technologies used to strengthen security of a network perimeter such as Network Address Translation (NAT), ASA policy and application inspect, and a zone-based firewall on Cisco routers. Candidates can prepare for this exam by taking the Cisco Edge Network Security (SENSS) course.
The following topics are general guidelines for the content likely to be included on the exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice.
1.0 Threat Defense 25%
1.1 Implement firewall (ASA or IOS depending on which supports the implementation)
1.1.a Implement ACLs
1.1.b Implement static/dynamic NAT/PAT
1.1.c Implement object groups
1.1.d Describe threat detection features
1.1.e Implement botnet traffic filtering
1.1.f Configure application filtering and protocol inspection
1.1.g Describe ASA security contexts
1.2 Implement Layer 2 Security
1.2.a Configure DHCP snooping
1.2.b Describe dynamic ARP inspection
1.2.c Describe storm control
1.2.d Configure port security
1.2.e Describe common Layer 2 threats and attacks and mitigation
1.2.f Describe MACSec
1.2.g Configure IP source verification
1.3 Configure device hardening per best practices
1.3.a Routers
1.3.b Switches
1.3.c Firewalls
2.0 Cisco Security Devices GUIs and Secured CLI Management 25%
2.1 Implement SSHv2, HTTPS, and SNMPv3 access on the network devices
2.2 Implement RBAC on the ASA/IOS using CLI and ASDM
2.3 Describe Cisco Prime Infrastructure
2.3.a Functions and use cases of Cisco Prime
2.3.b Device Management
2.4 Describe Cisco Security Manager (CSM)
2.4.a Functions and use cases of CSM
2.4.b Device Management
2.5 Implement Device Managers
2.5.a Implement ASA firewall features using ASDM
3.0 Management Services on Cisco Devices 12%
3.1 Configure NetFlow exporter on Cisco Routers, Switches, and ASA
3.2 Implement SNMPv3
3.2.a Create views, groups, users, authentication, and encryption
3.3 Implement logging on Cisco Routers, Switches, and ASA using Cisco best practices
3.4 Implement NTP with authentication on Cisco Routers, Switches, and ASA
3.5 Describe CDP, DNS, SCP, SFTP, and DHCP
3.5.a Describe security implications of using CDP on routers and switches
3.5.b Need for dnssec
4.0 Troubleshooting, Monitoring and Reporting Tools 10%
4.1 Monitor firewall using analysis of packet tracer, packet capture, and syslog
4.1.a Analyze packet tracer on the firewall using CLI/ASDM
4.1.b Configure and analyze packet capture using CLI/ASDM
4.1.c Analyze syslog events generated from ASA
5.0 Threat Defense Architectures 16%
5.1 Design a Firewall Solution
5.1.a High-availability
5.1.b Basic concepts of security zoning
5.1.c Transparent & Routed Modes
5.1.d Security Contexts
5.2 Layer 2 Security Solutions
5.2.a Implement defenses against MAC, ARP, VLAN hopping, STP, and DHCP rogue attacks
5.2.b Describe best practices for implementation
5.2.c Describe how PVLANs can be used to segregate network traffic at Layer 2
6.0 Security Components and Considerations 12%
6.1 Describe security operations management architectures
6.1.a Single device manager vs. multi-device manager
6.2 Describe Data Center security components and considerations
6.2.a Virtualization and Cloud security
6.3 Describe Collaboration security components and considerations
6.3.a Basic ASA UC Inspection features
6.4 Describe common IPv6 security considerations
6.4.a Unified IPv6/IPv4 ACL on the ASA
QUESTION 1
All 30 users on a single floor of a building are complaining about network slowness. After
investigating the access switch, the network administrator notices that the MAC address table is
full (10,000 entries) and all traffic is being flooded out of every port. Which action can the
administrator take to prevent this from occurring?
A. Configure port-security to limit the number of mac-addresses allowed on each port
B. Upgrade the switch to one that can handle 20,000 entries
C. Configure private-vlans to prevent hosts from communicating with one another
D. Enable storm-control to limit the traffic rate
E. Configure a VACL to block all IP traffic except traffic to and from that subnet
Answer: A
Explanation:
QUESTION 2
A network printer has a DHCP server service that cannot be disabled. How can a layer 2 switch be
configured to prevent the printer from causing network issues?
A. Remove the ip helper-address
B. Configure a Port-ACL to block outbound TCP port 68
C. Configure DHCP snooping
D. Configure port-security
Answer: C
Explanation:
QUESTION 3
A switch is being configured at a new location that uses statically assigned IP addresses. Which
will ensure that ARP inspection works as expected?
A. Configure the ‘no-dhcp’ keyword at the end of the ip arp inspection command
B. Enable static arp inspection using the command ‘ip arp inspection static vlan vlan-number
C. Configure an arp access-list and apply it to the ip arp inspection command
D. Enable port security
Answer: C
Explanation:
QUESTION 4
Which of the following would need to be created to configure an application-layer inspection of
SMTP traffic operating on port 2525?
A. A class-map that matches port 2525 and applying an inspect ESMTP policy-map for that class
in the global inspection policy
B. A policy-map that matches port 2525 and applying an inspect ESMTP class-map for that policy
C. An access-list that matches on TCP port 2525 traffic and applying it on an interface with the
inspect option
D. A class-map that matches port 2525 and applying it on an access-list using the inspect option
Answer: A
Explanation:
QUESTION 5
Which command is used to nest objects in a pre-existing group?
A. object-group
B. network group-object
C. object-group network
D. group-object
Answer: D
Explanation:
Click here to view complete Q&A of 300-206 exam
Certkingdom Review
Best Cisco 300-206 Certification, Cisco 300-206 Training at certkingdom.com